Loading experience0%
Top
Precision kit 01

Xcrewdriver

Torque, redesigned.

Interactive 3D view of the Xcrewdriver kit: the anodized aluminum case with 22 precision bits and the electric screwdriver docked inside. Scrolling slides the sleeve off, lifts the driver out of the tray and shows its specs.

Finish

Graphite anodized aluminum

1.8 mm wall, bead-blasted
A person tightening a drone motor with the Xcrewdriver, the open bit case on the bench
  • 62.5 x 203 mmOuter size
  • Open endsSlide-off sleeve
  • 540 gFull kit
A person assembling a racing drone on a workbench, tightening a motor mount with the XcrewdriverField use

Drone builds, to spec.

Motor mounts and prop nuts at a set torque. M2 screws stay intact.

Slide the sleeve.

An aluminum sleeve, open at both ends, slides over the inner tray. Pull it off and the driver sits docked between the bits, ready in one move.

A hand holding the Xcrewdriver over a circuit board, the bit seated on a screwFitFriction slide, magnet-assisted stop

A magnet pulls the sleeve home and holds it closed. Slide it off with one thumb.

The bead-blasted aluminum body of the Xcrewdriver in a hand, tightening a screw on a circuit boardShell1.8 mm anodized aluminum

Bead-blasted graphite wall, open at both ends. It slides off along the long axis without a latch.

Everything in one kit.

22 bits in S2 steel, each in its own slot and labeled by size. Phones, laptops, consoles, drones.

Two hands working on a racing drone with the Xcrewdriver, the 22-bit case open beside it
22Precision bits
  • PhillipsPH000 to PH2x5
  • Tri-wingY0.6 to Y3.0x6
  • U-typeU2.0 to U3.0x3
  • Numbered0.8 to 2.5x4
  • S-typeS0 and S1x2
  • W-typeW1.5x1
  • SlottedSL3.0x1

Built around the motor.

The driver leaves the tray. Inside the 24 mm body: motor, clutch, gearbox and battery, in a straight line.

A hand holding the Xcrewdriver like a pen, thumb on the button
Driver body24 mm280 g, one-hand grip
4 N·mMax torque6-step clutch
A hand holding the Xcrewdriver like a pen, tightening a screw on a circuit board
  • 45 minUSB-C charge
  • 1500 rpmBrushless
12 hRuntime

The numbers.

  • 4N·mMax torque
  • 1500rpmNo-load speed
  • 12hRuntime, light duty
  • 280gDriver weight
  • 45minFull charge, USB-C
  • 22bitsS2 steel, in the case

Out in the field.

Drone benches, repair desks and site bags. The same driver and the same 22 bits, wherever the screws are.

Hands tightening a drone motor with the Xcrewdriver, the bit tray and aluminum sleeve on the bench
Drones

Motor mounts

Set the clutch once. Every M2 screw seats at the same torque.

A hand holding the Xcrewdriver over a circuit board, the bit seated on a screw
Electronics

Board work

Pen grip, thumb on the button. Fine control on standoffs and shields.

Close-up of an aluminum bit tray, each bit in its own slot with its size printed below
The tray

Every bit labeled

Each bit sits in its own slot with its size printed below it.

Two hands working on a racing drone with the Xcrewdriver, the 22-bit case open beside it
Bench

Two-hand assembly

The magnet holds the screw. The other hand keeps the frame still.

The bead-blasted aluminum body of the Xcrewdriver in a hand, tightening a screw on a circuit board
Repairs

Laptops and consoles

Tri-wing and Phillips down to PH000. No stripped heads.

An open aluminum bit case with two trays of labeled bits on a dark surface
On the go

One case, one pocket

203 mm long, 540 g with everything inside. USB-C on the road.